產品展示PRODUCTS
自動上料機吸料風機 分離式吸料機配套風機
Automatic feeder suction fan, separable suction fan for feeder
自動上料吸料風機性能特點：
1. 超型 , 無噪音 : 馬達直接運轉，在通過加上體式的銷音設施，改進了高壓風機噪音的現像 , 從而達到的效果。
2. 可靠性高當使用情況變化時，機器仍可安全運轉。除了葉輪之外，高壓鼓風機沒有其他動作，因此可靠性之高幾乎免維修。使用*且散熱良精密外側軸承，因此它具有下列優點：高壓縮比；軸承運轉溫度低；潤滑油脂壽命長；免保養。
3. 安裝容易 配備齊全，可隨時安裝與使用，供壓縮空氣或用于抽真空，也可任意安裝于水平或垂直的方向。
4. 無油無污染 葉輪旋轉時，不與任何部分零件接觸，免潤滑，因此可保證無污染。
5. 高品質 經過20 年的業制造經驗，精密機械設計加上慎重電機配合標準儀器測試，使用所有零件均能達到高品質要求，運用標準 ip54 ， F 級馬達效率高，故障極少，馬達與鼓風機之間有軸封分試，預防異物進入。同時為確保功能效果，每臺鼓風機在出廠前均經過嚴格測試。
Automatic feeding machine suction fanPerformance characteristics:
1. Super size, no noise: The motor is directly driven, and the noise of the high-pressure blower is improved by adding a body-type silencer, thus achieving the desired effect.
2. High reliability: the machine can still operate safely when the operating conditions change. In addition to the impeller, the high-pressure blower has no other action, so its reliability is almost maintenance-free. It has the following advantages due to the use of * and good heat dissipation precision outer bearing: high compression ratio; The bearing operation temperature is low; Lubricating grease has a long service life; No maintenance required.
3. Easy to install, fully equipped, can be installed and used at any time, for compressed air or vacuum suction, can also be arbitrarily installed in the horizontal or vertical direction.
4. Oil-free and pollution-free When the impeller rotates, it does not come into contact with any part of the machine, so it is lubricant-free and pollution-proof.
5. High quality After 20 years of industry manufacturing experience, precision mechanical design combined with careful motor matching and standard instrument testing, All parts can meet the high-quality requirements, using standard IP54, F-class motor with high efficiency, very few failures, there is a shaft seal between the motor and the blower to prevent foreign objects from entering. At the same time, in order to ensure the function effect, each blower is strictly tested before leaving the factory.
自動上料吸料風機各行業應用激光雕刻設備、燃燒降氧機、卷煙濾嘴成型機、霧化干燥機、、絲網印刷機、照相制版機、注塑機、自動上料烘干機、液體灌裝機、粉末灌裝機、電焊設備、電影機械、紙張運送、干洗衣服、清潔用途、空氣除塵、干瓶除水、氣體傳送、送料、吸料、物料收集、中央集塵環境保護、絲網印刷、電鍍行業、除塵集塵、食品機械、包裝設備、灌裝行業、玻璃制品、氣流輸送、水處理曝氣等相關行業和機械。
Automatic feeding machine suction fanLaser engraving equipment, combustion oxygen reduction machine, Cigarette filter mouthpiece forming machine, atomization drying machine, screen printing machine, photographic printing machine, injection molding machine, automatic feeding drying machine, liquid filling machine, powder filling machine, electric welding equipment, film machinery, paper transportation, dry cleaning clothes, cleaning purposes, Air dust removal, dry bottle water removal, gas transmission, feeding, suction, material collection, central dust collection, environmental protection, screen printing, electroplating industry, dust collection, food machinery, packaging equipment, filling industry, glass products, air flow transmission, water treatment aeration and other related industries and machinery.
自動上料吸料風機操作及維護：
1.安裝竣工后的鼓風機在啟動前應行手動轉動，檢查有無異常碰撞與摩擦，電動機的旋向是否正確，進出口閥門是否在小流量狀態。
2.風機運行時應注意風機和電機內部有無異常聲響，漏油，異常的振動或軸承溫升過高，電機電流過，地腳松動等不正?，F(xiàn)象，并及時排除。
3.新風機使用5000小時后要更換軸承油脂。
4.檢修：機殼檢修時先松開水平中分面上螺釘，打開上半機殼和兩側軸承箱上蓋，取出轉子即可對轉子或機殼進行維修。檢修時應特別注意葉輪葉片是否斷裂，有無裂紋，主軸是否彎曲。裝拆上班機殼前，必須謹慎避免裝拆過程中因上半機殼擺動而損壞轉子。
5.風機出廠時貨用戶停機期間均應將風機進出口蓋，以防止雜物落入風機內腔造成事故。
6.風機每工作半年需檢修次，清楚風機流道內積塵和油污。
Automatic feeding machine suction fanOperation and maintenance:
1. Before the blower is started, it should be manually rotated after the installation is completed to check if there are any abnormal collisions and friction, whether the direction of the motor is correct, and whether the inlet and outlet valves are in the small flow state.
2. When the fan is running, attention should be paid to whether there are any abnormal sounds, oil leakage, abnormal vibration or excessive bearing temperature rise in the fan and motor, excessive motor current, loose foot, and other abnormal phenomena, and they should be eliminated in time.
3. The bearing grease should be replaced after 5000 hours of use.
4. Inspection: When inspecting the casing, first loosen the screw on the horizontal center plane, open the upper half of the casing and the cover of the two sides of the bearing box, and take out the rotor to repair the rotor or the casing. During maintenance, special attention should be paid to whether the blade of the impeller is broken, whether there are cracks, and whether the main shaft is bent. Before disassembling and reassembling the working machine casing, it is necessary to be cautious and avoid damaging the rotor during the disassembly and reassembly process due to the movement of the upper casing.
5. The inlet and outlet covers of the fan should be closed when the fan is not in use to prevent debris from falling into the fan's internal cavity and causing an accident.
6. The fan should be inspected once every six months to clear dust and oil in the fan duct.
自動上料吸料風機我們的服務理念：
1.TWYX售前服務：阜風公司為您提供詳細的風機技術參數，給予您選出更合適您使用的風機。
2.TWYX售中服務：我公司專職服務人員和您一起跟蹤貨物，直到貨物安全到達您的手里。
3.TWYX售后服務：公司銷售人員為您簡單了解講訴風機的原理，及注意事項。
4.TWYX質量保證：我們?nèi)盗挟a(chǎn)品12個月質量保證。
5.如果有不明白的操作可咨詢我公司專業的技術專員，為您講解操作方案。
6.TWYX公司將提供耐心、友好、熱情的支持，可靠保障客戶安全使用及運營。
Automatic feeding machine suction fanOur service philosophy:
1. TWYX pre-sales service: Furong Company provides you with detailed fan technical parameters, giving you to choose the fan more suitable for your use.
2. TWYX sales service: Our company's dedicated service personnel will follow up with you until the goods arrive safely in your hands.
3. TWYX after-sales service: the company sales staff will explain the principle and precautions of the fan to you briefly.
4. TWYX Quality Assurance: 12 months quality assurance for all our products.
5. If there is any operation that you do not understand, you can consult our company's professional technical specialist to explain the operation plan for you.
6. TWYX will provide patient, friendly, and enthusiastic support to ensure the safe use and operation of customers.
自動上料機吸料風機 分離式吸料機配套風機
Automatic feeder suction fan, separable suction fan for feeder
